The XHHV535-2TSB cable fault location system is used to detect the main insulation fault of power cables with voltage levels of 35kV and below and calibrate the cable length. This system consists of two parts: a cable fault tester and a high-voltage pulse generator.
The cable fault tester adopts a simple operating software interface, centralized control by a single-chip microcomputer,touch-type operation, and a built-in large capacity lithiumion battery. It is stable, reliable, and easy to use. An independent power supply and power supply system are used to prevent power supply interference during impact discharge.
This cable fault test system is suitable for low-resistance, short-circuit, open-circuit and broken wire faults of power cables,high-frequency coaxial cables, street light cables, and underground wires of various materials with different cross-sections and different media, as well as high-resistance leakage and high-resistance flash over faults.
Technical Parameters
| The surge HV voltage | 0-8kv/16kv/32kv |
| High voltage side current | 0-60mA |
| Inside capacitor | 2μF/32kV,8μF/16kV,32μF/8kV |
| Surge time | Auto surge about 7s, also can control by hands. |
| Surge energy | 1024J |
| Surge power | 2KVA |
| Weight | not more than 120kg |
| Power supply | AC220V±15%, 50Hz±2Hz |
| Environment temperature: | Environment temperature: |
Cable fault pre-locator parameters:
• Sampling frequency: 1MHz~400MHz;
• Low voltage pulse amplitude: 300V±15%;
• Distance measurement range: ≥120km;
• Test range: 100m/300m/500m/1km/3km/5km/10km/25km/50km/100km;
• Pulse width: 0.15uS/0.30uS/0.60uS/1.20uS/2.4uS/5.0uS/7.5uS/10uS;
• Minimum resolution: 0.07m;
• Test blind area: ≤10m;
• Measurement error: ≤±(0.5%×L+1m), L is the cable length;
• Working power supply: built-in 10.4AH lithium battery; charging time is about 2 hours, working time is 5 hours
XHDD503E Cable fault pinpointer
XHDD503E cable fault pinpointer uses the acoustic-magnetic synchronization principle of vibration pickup and electromagnetic induction to determine the specific location of the cable fault point. With the help of a high-voltage pulse generator, the fault point is flashed and discharged. The physical phenomena such as vibration waves, sound waves and electromagnetic waves generated by the flash over discharge of the fault point are collected by the dedicated probe of the positioning instrument. After intelligent processing by the host, the fault distance and output fault sound are displayed. Finally, the precise location of the fault point is judged by the tester's hearing and vision. That is, the precise positioning task of the cable fault point "directly above the cable, within the rough measurement range" is completed.
XHDD503E cable fault pinpointer is suitable for low-resistance, short-circuit, open-circuit, and broken-wire faults of various
power cables, coaxial cables, and low-voltage cables and wires with different voltage levels, different cross-sections, and
different media, as well as leakage and flash over high-resistance faults.
Main parameters:
Sound channel-Bandwidth
l All-pass: 100Hz~1600Hz.
l Low pass: 100Hz~300Hz.
l High pass: 160Hz~1600Hz.
l Band pass: 200Hz~600Hz.
Channel adjustment: 8 levels of sound, magnetic and voltage.
Sound output: Gain: 16 levels (0-112dB), Impedance: 350Ω
Detection range: 0.00-99.99ms, 75mV-75V
Detection accuracy: Positioning: ≤0.1m; Step voltage: ≤0.5m; Path: ≤0.5m
Working power supply: 4*18650 standard lithium battery.
Standby time: more than 8 hours
Ambient temperature: -25-65℃; Relative humidity: ≤90%
Volume dimensions: 428L×350W×230H
Overall weight: 7kg
|
|
Must-Have Portable Cable Fault Location System for Power Cable Insulation Detection Images
|
